Skip to content

Furnace Repair in Burbank, CA

Serving Burbank and nearby cities. Tell us about the job and we’ll call you back to confirm the details.

Tell us what’s going on

Prefer to talk? (669) 201-5255

The short answer

Liberty HVAC Services repairs gas furnaces in Burbank homes in ZIP codes 91501, 91502, 91504, 91505, and 91506. We diagnose problems such as no heat, short cycling, ignition failures, and blower issues, then explain your repair options before any work starts. If your furnace is near the end of its life, we'll also walk you through replacement rules and rebate questions that apply to your address.

Burbank winters are mild, so most furnaces here sit idle for months and then get switched on during the first cold night of fall. That long rest is often when problems show up: a dusty burner that won't light, a blower that hums but doesn't move air, or a system that runs and runs without warming the house. Liberty HVAC Services repairs gas furnaces and the heating side of central systems for homeowners across Burbank, about 10 miles north of our Los Angeles base. We find what's actually wrong, explain it in plain terms, and fix it so your home is comfortable again.

Common Furnace Problems in Burbank Homes

Because heating season in Burbank is short, furnaces here tend to fail from sitting unused rather than from heavy wear. Dust builds up on burners and flame sensors over the summer, filters get forgotten, and small electrical issues go unnoticed until the heat is needed. Burbank sits inland, where summers run much hotter than near the coast, and some homes put furnaces in attics or garages where that heat can be hard on wiring and controls.

These are the issues we're called about most often:

  • Furnace runs but blows cool or lukewarm air
  • Burner lights briefly, then shuts off (often a dirty flame sensor)
  • No ignition at all, or repeated clicking without a flame
  • Furnace turns on and off in short cycles
  • Blower won't start, or runs constantly
  • Burning smell that lasts more than the first few minutes of the season
  • Loud banging, rattling, or squealing from the cabinet
  • Thermostat calls for heat but nothing happens

What Happens During a Furnace Repair Visit

We start by asking what you've noticed: when the problem began, what the furnace sounds like, and whether anything has changed recently. Then we check the system step by step, including the thermostat, power and gas supply, ignition sequence, flame sensor, limit and pressure switches, blower motor, filter, and venting.

Once we've found the cause, we tell you what's wrong and what it will take to fix it before we do the work. Many furnace problems are straightforward, like a failed igniter, a dirty sensor, or a clogged filter that's tripping a safety switch. If we find something that affects safety, such as a damaged heat exchanger or a venting problem, we'll show you what we found and explain why it matters.

Repair or Replace? What Burbank Homeowners Should Know

A repair is usually the right call when the furnace is otherwise sound and the part that failed is a common one. Replacement makes more sense when repairs keep coming back, key components are wearing out at the same time, or there's a safety issue that can't be reasonably fixed. We'll give you an honest view either way.

If you're considering a new gas furnace, know that South Coast AQMD Rule 1111 limits nitrogen oxide emissions from natural-gas fan-type central furnaces sold and installed in the Los Angeles region. The district has been amending the rule toward zero-emission requirements and sets and revises the compliance dates, so it's worth checking the current rule before you plan a replacement.

Some homeowners use a furnace failure as the moment to look at a heat pump, which handles both heating and cooling. Rebates for qualifying equipment depend on which utility serves your address, so we confirm the current offer before quoting it. The federal Energy Efficient Home Improvement Credit (25C) covered qualifying heat pumps placed in service before December 31, 2025, and isn't available for new installations after that date.

Safety Comes First

If you smell gas, leave the house and contact your gas utility or emergency services from outside. Don't flip switches or try to relight the furnace yourself. If a carbon monoxide alarm sounds, get everyone outside and call for help.

For less urgent issues, a few simple checks can save time: make sure the thermostat is set to heat, replace a dirty filter, confirm the furnace switch is on, and check that the breaker hasn't tripped. If the furnace still won't heat, it's time to schedule a repair.

Furnace Repair Across Burbank and Nearby

We serve homes throughout Burbank, including ZIP codes 91501, 91502, 91504, 91505, and 91506, in Los Angeles County. We also handle furnace repair in nearby communities, including West Hollywood, Beverly Hills, Culver City, Vernon, and Santa Monica.

More services in Burbank

Related

What to expect

How a visit goes

  1. Diagnose First

    We test the system and pinpoint the cause before suggesting parts or replacement, so you know what you're paying to fix and why.

  2. Clear Options

    When there's more than one way to solve a problem, we lay out each option, what it involves, and the tradeoffs, then let you decide.

  3. Current Rules and Rebates

    Local equipment rules and utility rebates change. We check the current requirements and the offers available for your address before planning an installation.

FAQ

Common questions

Why does my furnace smell like it's burning when I first turn it on?

Dust settles on the burners and heat exchanger over the warm months and burns off when the furnace first runs. A faint smell that fades within a short time is normal. If it lasts, gets stronger, or smells electrical, turn the system off and schedule an inspection.

My furnace lights and then shuts off right away. What causes that?

A dirty or failing flame sensor is a common cause. The furnace can't confirm a flame, so it shuts the gas off for safety. Restricted airflow, a venting issue, or a faulty switch can cause similar behavior, so a proper diagnosis is worth doing.

Do I need a furnace in Burbank if winters are mild?

Most Burbank homes still use heat on cool nights from late fall through early spring. Because the furnace runs less than in colder climates, it's especially important that it starts reliably and safely when you need it.

Can I replace my old gas furnace with the same type of unit?

Possibly, but new natural-gas furnaces installed in the Los Angeles region must meet South Coast AQMD Rule 1111, which the district has been amending toward zero-emission requirements. Check the current rule and compliance dates before planning a replacement.

Are there rebates for switching from a furnace to a heat pump in Burbank?

It depends on which utility serves your address, since rebate programs differ by utility. We confirm the current offer for your home before quoting it. The federal 25C tax credit no longer applies to heat pumps placed in service after December 31, 2025.

How often should I change my furnace filter?

Check it at the start of heating season and every month or two while the system is in use. Central systems that also run for cooling in summer use the same filter, so it may need changing more often than you'd expect.

Tell Us What's Going On With Your System

Whether your AC stopped cooling, your furnace won't start, or you're thinking about switching to a heat pump, contact Liberty HVAC Services. We'll ask a few questions, look at the system, and explain your options before any work begins.

Call (669) 201-5255 Request Service